Maintenance Report

Search Filter:

Showing 16,151-16,160 of 17,159 items.

#DateTypeDetailsFurnaceEquipmentActions
1615122 May 2020Scheduled MaintenanceELECTRODE BLOWER 2

1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.it is ok.
2. check panel board, clean, & tight all loose parts.clean and tighting all loose parts.
3. all parts clean by hand blower.		Furnace IIELECTRODE 2
1615222 May 2020Scheduled Maintenance ELECTRODE BLOWER 3

1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.it is ok.
2. check panel board, clean, & tight all loose parts.clean and tighting all loose parts.
3. all parts clean by hand blower.		Furnace IIELECTRODE 3
1615322 May 2020Scheduled MaintenanceFURNACE 2
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.it is ok.
2. check panel board, clean, & tight all loose parts.clean and tighten loose parts.
3. all parts clean by hand blower.
4. check solenoid valves.it is ok.		Furnace IIHYDRAULIC POWER PACK NO. 1
1615421 May 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 1


LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. check bearing condition it is ok. And greasing is done.
2. check the gearbox oil level, leakage, and fill if required. No leakage we fill some grease.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.greasing is done.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. Greasing is done.
2. check the gearbox oil level, leakage, and fill if required. It has leakage but we fill some grease.
3. check all fasteners and mounting bolts. It is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.

HT.
1. check rope drum, hook, rope condition. greasing of rope. It is ok. Greasing is done.
2. check all fasteners and mounting bolts. It is ok.
3. check frame welding conditions. It is ok.		OtherTAPPING SEC. CRANE NO. 1
1615521 May 2020Scheduled MaintenanceCHIPPING YARD E.O.T. CRANE 1
LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing.checked and greasing is done.
2. check the gearbox oil level, leakage, and fill if required. we found leakage so we fill some amount of grease.
3. check all fasteners and mounting bolts. it is ok.
4. check frame welding conditions. it is not ok. its shaft condition is not good.
5. check end traveling gears condition and do the greasing. it is ok.

CT.
gears are ok. it is good in condition.
HT.
1. check rope drum, hook, rope condition. greasing of rope.rope greasing is done. it is in good condition.
2. check the thruster drum condition and its brake tightness.no thruster.
3. check all fasteners and mounting bolts. it is ok.
4. check frame welding conditions.it is ok.		OtherCHIPPING YARD CRANE NO. 1
1615621 May 2020Scheduled MaintenanceCHIPPING YARD E.O.T. CRANE 2


LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. greasing is done. it is ok.
2. check the gearbox oil level, leakage, and fill if required. no leakage but we fill grease.
3. check all fasteners and mounting bolts. it is ok.
4. check frame welding conditions. it is ok.
5. check end traveling gears condition and do the greasing.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. greasing is done. it is ok.
2. check the gearbox oil level, leakage, and fill if required. no leakage but we fill grease.
3. check all fasteners and mounting bolts. it is ok.
4. check frame welding conditions. it is ok.
5. check end traveling gears condition and do the greasing.it is ok. greasing is done.

HT.
1. check rope drum, hook, rope condition. greasing of rope. greasing is done. it is ok.
2. check the thruster drum condition and its brake tightness. no thruster.
3. check all fasteners and mounting bolts. It is ok.
4. check frame welding conditions.it is ok.		OtherCHIPPING YARD CRANE NO. 2
1615721 May 2020Scheduled MaintenanceTELPHER FOR F1
1. checking the bearing, rollers condition, and do lubrication.check it is ok.
2. checking frames welding condition.it is ok.
3. checking cotter pin and its failure condition. it is ok.


OtherTELPHER (FURNACE 1)
1615821 May 2020Scheduled MaintenanceTELPHER FOR F2

1. checking the bearing, rollers condition, and do lubrication.check it is ok.
2. checking frames welding condition.it is ok.
3. checking cotter pin and its failure condition. it is ok.

OtherTELPHER ( FURNACE 2)
1615921 May 2020Scheduled MaintenancePOLLUTION ID FANS (Furnace 1)
1. open cover and clean dust.
2. check the balancing of impeller and vibration isolation. IT IS OK. WE TIGHTS NUTS AND BOLTS OF PLUMMER BLOCKS. It's MAKING SOME VIBRATIONS WE INFORME IT TO HOD.
3. checked v belts condition and inform if its on critical stage. IT IS OK.
4. checked foundation bolts and nuts of Plummer blocks.
5. greasing the Plummer blocks is done.
6. checked the duct condition and remove dust from the duct. it is ok.
7. check stack condition and check its temperature. it is ok.		OtherPOLLUTION 1
1616021 May 2020Scheduled MaintenancePOLLUTION ID FANS FOR (Furnace 2)
1. open cover and clean dust.
2. check the balancing of impeller and vibration isolation. IT IS OK. WE TIGHTS NUTS AND BOLTS OF PLUMMER BLOCKS. It's MAKING SOME VIBRATIONS WE INFORME IT TO HOD.
3. checked v belts condition and inform if its on critical stage. IT IS OK.
4. checked foundation bolts and nuts of Plummer blocks.
5. greasing the Plummer blocks is done.
6. checked the duct condition and remove dust from the duct. it is ok.
7. check stack condition and check its temperature. it is ok.		OtherPOLLUTION 2