| 16111 | 25 May 2020 | Breakdown Maintenance | Here 1 tube light and 3 cfl lights changed. | Other | GUEST HOUSE | |
| 16112 | 25 May 2020 | Breakdown Maintenance | Chipping yard side light not working .We replace it by 400 W sodium lamp. | Other | LAMP | |
| 16113 | 25 May 2020 | Breakdown Maintenance | Weigh bridge side one LIGHT NOT working. We replace it by 400 W sodium lamp. | Other | LAMP | |
| 16114 | 25 May 2020 | Other | 10 A MCB with box fitting at tapping section for lighting purpose. | Other | LAMP | |
| 16115 | 24 May 2020 | Breakdown Maintenance | It's back centre tyre is puncherd. We repaired it. Now it's ok. | Other | TATA TIPPER | |
| 16116 | 23 May 2020 | Scheduled Maintenance | TILTING HOPPER
1. greasing all bushes.greasing is done.
2.hydraulic pump and motor coupling.it is ok.
3. checking the hydraulic oil level and if not then fill.it is ok.
4. check hopper welding sections.
It is ok.
CONVEYOR NO 1
1. greasing of bearings.greasing is done.
2. lubrication of rollers and check conditions.it is ok.
3. check belt status ( if damaged than inform and change) and also check tightness, speed.it is ok.belt is not good we need to change it.
4. gearbox oil level check and if not then fill as per requirement.grease fill is done.
5. check coupling and key ( if damaged than inform and change) and do the greasing.it is ok.
6. check the drum condition.it is ok.
7. check mounting frame welding condition.it is ok.
8. check rollers condition and if not good then change.
CRUSHER crusher is out due to small size material.
1. check the crusher foundation.
2. check V belts condition.
3. do greasing.
4. check spring rod condition and gap between plates.
VIBRATOR
1. check the spring condition.it is ok.
2. check V belts condition.it is ok.
3. check vibrations if not good then adjust.it is ok.
4. check the frame welding condition.greasing is done.in bearings.
ROLLER
1. check roller speed.it is ok.
2.greasing of bearings.greasing is done.
3.gearbox oil level check and if not then fill as per requirement.it is ok.
4. check coupling and key ( if damaged than inform and change) and do the greasing.it is ok.
5. check the drum condition.
6. check the mounting frame welding condition.it is ok.
DISCHARGE CONVEYOR
1. greasing of bearings.Greasing is done.
2. lubrication of rollers and check conditions.it is ok.
3. check belt status ( if damaged than inform and change) and also check tightness, speed.it is ok.
4. gearbox oil level check and if not then fill as per requirement.it is ok. Fill some grease.
5. check coupling and key ( if damaged than inform and change) and do the greasing.it is ok.
6. check the drum condition.
7. check mounting frame welding condition.it is ok.
8. check rollers condition and if not good then change. | Other | WASHING PLANT | |
| 16117 | 23 May 2020 | Scheduled Maintenance | WASHING PLANT TILTING HOPPER, CONVEYOR NO 1, CRUSHER, VIBRATOR, ROLLER, DISCHARGE CONVEYOR , WATER PUMP
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. All motors checked .It's in good condition.
2. check panel board, clean, & tight all loose parts.its clean and loose parts tight.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly. It is ok. Mechanical people weld it's foundation.
5. check the high mast lights also.it is ok. | Other | WASHING PLANT | |
| 16118 | 23 May 2020 | Other | Increase SPREY NOZZLES IN POLLUTION PIPELINE. | Other | POLLUTION 2 | |
| 16119 | 23 May 2020 | Other | One water filter fitting for pollution water. | Other | POLLUTION 2 | |
| 16120 | 23 May 2020 | Breakdown Maintenance | Its incoming cable is cut. It is repaired. Now its working | Other | TELPHER (FURNACE 1) | |
 white.png){kind=small}