| 16031 | 02 Jun 2020 | Scheduled Maintenance | F1- GRANULATION MOTOR 1,2 WATER CIRCULATION PUMP MOTOR 1,2,3, SUBMERSIBLE PUMP MOTOR 1,2, POLLUTION WATER PUMP MOTOR
NO 1
F2- GRANULATION MOTOR 1,2, POLLUTION WATER PUMP MOTOR NO 1, OFFICE SUBMERSIBLE PUMP MOTOR 1,
WASHING PLANT SUBMERSIBLE PUMP MOTOR1
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. it's ok.
2. check panel board, clean, & tight all loose parts.clean and tight all loose parts.
3. all parts clean by hand blower.
4. water circulation pump motor greasing. greasing is done. | Other | PUMP | |
| 16032 | 02 Jun 2020 | Breakdown Maintenance | BC 3 side railing welding work is done. | Other | RMHS BELT CONVEYOR NO.3 | |
| 16033 | 02 Jun 2020 | Breakdown Maintenance | its starter Bendex drive coil is damaged. we repair it and replace it by old one. Now it's working. | Other | LODER NO.2 | |
| 16034 | 02 Jun 2020 | Breakdown Maintenance | its silencer coupling gasket is damaged. we repair it now it's working. | Other | JCB 4DX | |
| 16035 | 02 Jun 2020 | Breakdown Maintenance | It's centre rear tyre is puncherd. We repaired it now it's working. | Other | TATA TIPPER | |
| 16036 | 01 Jun 2020 | Scheduled Maintenance | TAPPING SECTION E.O.T. CRANE 3
LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. Checking and greasing are done. It is ok.
2. check the gearbox oil level, leakage, and fill if required. No leakage but we fill grease.
3. check all fasteners and mounting bolts. It is OK.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.
CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. It is ok.
2. check the gearbox oil level, leakage, and fill if required. Leakage is there so we fill grease.
3. check all fasteners and mounting bolts. It is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok. And greasing is done.
HT.
1. check rope drum, hook, rope condition. greasing of rope. It is ok.
2. check the thruster drum condition and its brake tightness. It is ok.
3. check all fasteners and mounting bolts. It is ok.
4. check frame welding conditions. It is ok.
5. gearbox is leakage and makes too much sound so we put grease. | Other | TAPPING SEC. CRANE NO. 3 | |
| 16037 | 01 Jun 2020 | Scheduled Maintenance | ALL CONVEYORS
BC 1, BC 2, BC 3, BC 4, BC 5, BC 6, BC 7
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. IT IS OK.
2. check panel board, clean, & tight all loose parts. CLEAN AND TIGHTENING ALL LOOSE PARTS.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.IT IS OK. | Other | RMHS CONVEYOR | |
| 16038 | 01 Jun 2020 | Scheduled Maintenance | ALL VIBRATORS
check Vibro feeders coil connection, its condition and ensure its working properly with adjusting its vibrations.CHECKING AND ADJUSTING VIBRATION IS DONE. IT IS OK. | Other | RMHS VIBRO FEEDER | |
| 16039 | 01 Jun 2020 | Scheduled Maintenance | ALL CONVEYORS
BC 1, BC 2, BC 3, BC 4, BC 5, BC 6, BC 7
1. greasing of bearings. it is done.
2. lubrication of rollers and check conditions. it is ok.
3. check belt status ( if damaged than inform and change) and also check tightness, speed. ALL BELT CONVEYORS CONDITION IS OK EXCEPT BC 2. WE NEED TO CHANGE IT. WE INFORM IT TO HOD. WE CHANGE IT AS SOON AS POSSIBLE.
4. gearbox oil level check and if not then fill as per requirement. ALL GEARBOX ARE OK.
5. check coupling and key ( if damaged than inform and change) and do the greasing. IT IS OK. GREASING IS DONE.
6. check the drum condition. IT IS OK.
7. check mounting frame welding condition. IT IS OK.
8. check rollers condition and if not good then change.we changeONE ROLLER OF BC 6. | Other | RMHS CONVEYOR | |
| 16040 | 01 Jun 2020 | Breakdown Shutdown | its hydraulic slipping and down clamping cylinder is leakage. we fill 50 ltr oil in the tank and checked. we replace it with spare cylinders. | Furnace I | ELECTRODE 1 | |
 white.png){kind=small}