| 15871 | 18 Jun 2020 | Scheduled Maintenance | TELPHER FOR F1
1. checking the bearing, rollers condition, and do lubrication.check it is ok.
2. checking frames welding condition.it is ok.
3. checking cotter pin and its failure condition. it is ok
| Other | TELPHER (FURNACE 1) | |
| 15872 | 18 Jun 2020 | Scheduled Maintenance | TELPHER FOR F2
1. checking the bearing, rollers condition, and do lubrication.check it is ok.
2. checking frames welding condition.it is ok.
3. checking cotter pin and its failure condition. it is ok
| Other | TELPHER ( FURNACE 2) | |
| 15873 | 18 Jun 2020 | Scheduled Maintenance | POLLUTION ID FANS (Furnace 1)
1. open cover and clean dust.clean and balancing is done.
2. check the balancing of impeller and vibration isolation.it is ok.
3. check v belts condition and inform if it's on critical stage.it is ok.
4. check foundation bolts and nuts of Plummer blocks.it is ok.
5. greasing the Plummer blocks.greasing is done.
6. check the duct condition and remove dust from the duct.
7. check stack condition and check its temperature. it is ok. | Other | POLLUTION 1 | |
| 15874 | 18 Jun 2020 | Scheduled Maintenance | POLLUTION ID FANS FOR (Furnace 2)
1. open cover and clean dust.clean and balancing is done.
2. check the balancing of impeller and vibration isolation.it is ok.
3. check v belts condition and inform if it's on critical stage.it is ok.
4. check foundation bolts and nuts of Plummer blocks.it is ok.its making vibrations because of too much dust inside. so we clean and fighting all foundations bolts.
5. greasing the Plummer blocks.greasing is done.
6. check the duct condition and remove dust from the duct.
7. check stack condition and check its temperature. it is ok. | Other | POLLUTION 2 | |
| 15875 | 18 Jun 2020 | Scheduled Maintenance | CHIPPING YARD E.O.T. CRANE 1
LT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.
CT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.
HT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly. | Other | CHIPPING YARD CRANE NO. 1 | |
| 15876 | 18 Jun 2020 | Scheduled Maintenance | TELPHER FOR F1
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
| Other | TELPHER (FURNACE 1) | |
| 15877 | 18 Jun 2020 | Scheduled Maintenance | TELPHER FOR F2
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
| Other | TELPHER ( FURNACE 2) | |
| 15878 | 18 Jun 2020 | Scheduled Maintenance | POLLUTION ID FANS FOR F1
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
4. MOTOR GREASING. | Other | POLLUTION 1 | |
| 15879 | 18 Jun 2020 | Scheduled Maintenance | POLLUTION ID FANS FOR F2
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
4. MOTOR GREASING. | Other | POLLUTION 2 | |
| 15880 | 18 Jun 2020 | Scheduled Maintenance | Here we fitting one setting tank. | Other | WASHING PLANT | |
 white.png){kind=small}