Maintenance Report

Search Filter:

Showing 15,281-15,290 of 17,159 items.

#DateTypeDetailsFurnaceEquipmentActions
1528127 Aug 2020Scheduled MaintenancePOLLUTION ID FANS FOR F1
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
4. MOTOR GREASING.
OtherPOLLUTION 1
1528227 Aug 2020Scheduled MaintenancePOLLUTION ID FANS FOR F2
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
4. MOTOR GREASING.
OtherPOLLUTION 2
1528327 Aug 2020Breakdown Maintenancevibro feeder no.8 not vibrating due to alignment problem alignment done now working.OtherRMHS VIBRO FEEDER
1528426 Aug 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 1

LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. checked its ok. we open and fill grease.
2. check the gearbox oil level, leakage, and fill if required. gearbox has leakage. we fill grease.
3. check all fasteners and mounting bolts. it's ok.
4. check frame welding conditions. it's ok.
5. check end traveling gears condition and do the greasing. greasing is done.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. coupling is ok.
2. check the gearbox oil level, leakage, and fill if required. we fill grease.
3. check all fasteners and mounting bolts. it's ok.
4. check frame welding conditions. its ok.
5. check end traveling gears condition and do the greasing.

HT.
1. check rope drum, hook, rope condition. greasing of rope. already grease is on the rope.
2. check the thruster drum condition and its brake tightness. no truster. it's ok.
3. check all fasteners and mounting bolts. it's ok.
4. check frame welding conditions. its ok.		OtherTAPPING SEC. CRANE NO. 1
1528526 Aug 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 2


LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. check bearing condition it is ok. And greasing is done.
2. check the gearbox oil level, leakage, and fill if required. No leakage we fill some grease.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.greasing is done.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. Greasing is done.
2. check the gearbox oil level, leakage, and fill if required. It has leakage but we fill some grease.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.

HT.
1. check rope drum, hook, rope condition. greasing of rope. It is ok. Greasing is done.
2. check all fasteners and mounting bolts. It is ok.
3. check frame welding conditions. It is ok.
4. gearbox oil level is ok.		OtherTAPPING SEC. CRANE NO. 2
1528626 Aug 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 3


LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. its ok.
2. check the gearbox oil level, leakage, and fill if required. gearbox has small leakage. we fill grease.
3. check all fasteners and mounting bolts. motor and gearbox do not have foundation bolts. we mount foundation bolts. its coupling side bolt is going loose. we tight it also.
4. check frame welding conditions. it's ok.
5. check end traveling gears condition and do the greasing. no end traveling gears.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. it's ok. coupling greasing is done.
2. check the gearbox oil level, leakage, and fill if required. gearbox side leakage. we fill grease.
3. check all fasteners and mounting bolts. all foundation bolts are in good condition.
4. check frame welding conditions. it's ok.
5. check end traveling gears condition and do the greasing. greasing is done.

HT.
1. check rope drum, hook, rope condition. greasing of rope. already grease is there.
2. check the thruster drum condition and its brake tightness. the thruster is in good condition.
3. check all fasteners and mounting bolts. it's in good condition.
4. check frame welding conditions. it's ok.
5. we open the gearbox and check it. then we found that 3 nos. bearing is damaged. so we change it. the bearing numbers are 6206.
and we found that the gears are damaged. so we weld the teeth and grind. after that, we change 2 nos. keys. and foundation nuts.after that we fitting it. now it's ok.		OtherTAPPING SEC. CRANE NO. 3
1528726 Aug 2020Scheduled Maintenance3RD FLOOR CARBON PASTE LIFTING CRANE

LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. Greasing is done.
2. check the gearbox oil level, leakage, and fill if required. It is OK.we fill grease due to leakage.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions.it is ok.
5. check end traveling gears condition and do the greasing. It is ok.greasing is done.
6.
CT.
It is ok. Gear bearing is ok.w


HT.
It's is ok. Pulley's condition is ok.no greasing because of grease is already there.		OtherCARBON PASTE LIFTING CRANE
1528826 Aug 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 1

LT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

CT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

HT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly. 		OtherTAPPING SEC. CRANE NO. 1
1528926 Aug 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 2

LT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

CT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

HT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly. 		OtherTAPPING SEC. CRANE NO. 2
1529026 Aug 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 3

LT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.
2. check panel board, clean, & tight all loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.

CT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.
2. check panel board, clean, & tight all loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.

HT. the motor is not in good condition.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.
2. check panel board, clean, & tight all loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.
OtherTAPPING SEC. CRANE NO. 3