Maintenance Report

Search Filter:

Showing 15,021-15,030 of 17,159 items.

#DateTypeDetailsFurnaceEquipmentActions
1502124 Sep 2020Scheduled MaintenanceTELPHER FOR F2
1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
OtherTELPHER ( FURNACE 2)
1502224 Sep 2020Scheduled Maintenance1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
4. MOTOR GREASING.		OtherPOLLUTION 1
1502324 Sep 2020Scheduled Maintenance1.check motor condition ( amp, volt, and connectivity) if the noise coming than inform. motor condition checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight all loose parts.
3. all parts clean by hand blower.
4. MOTOR GREASING.		OtherPOLLUTION 2
1502424 Sep 2020Breakdown Maintenancecharging chute no 3 was repaired. now its ok.Furnace IICHARGING CHUTE NO. 3
1502524 Sep 2020Scheduled Maintenancedue to the small width of the belt charge coming down. we extend the chute and mount side rubbers from inside and fix one separator.Other RMHS BELT CONVEYOR NO.6
1502623 Sep 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 2

LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. checked its ok. we open and fill grease.
2. check the gearbox oil level, leakage, and fill if required. gearbox has leakage. we fill grease.
3. check all fasteners and mounting bolts. it's ok.
4. check frame welding conditions. it's ok.
5. check end traveling gears condition and do the greasing. greasing is done.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. coupling is ok.
2. check the gearbox oil level, leakage, and fill if required. we fill grease.
3. check all fasteners and mounting bolts. it's ok.
4. check frame welding conditions. it's ok.
5. check end traveling gears condition and do the greasing.

HT.
1. check rope drum, hook, rope condition. greasing of rope. already grease is on the rope. its break has a problem. we fix it. now its ok.
2. check the thruster drum condition and its brake tightness. no truster. it's ok.
3. check all fasteners and mounting bolts. it's ok.
4. check frame welding conditions. it's ok.		OtherTAPPING SEC. CRANE NO. 2
1502723 Sep 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 3

LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. check bearing condition it is ok. And greasing is done.
2. check the gearbox oil level, leakage, and fill if required. No leakage we fill some grease.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.greasing is done.

CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. Greasing is done.
2. check the gearbox oil level, leakage, and fill if required. It has leakage but we fill some grease.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions. It is ok.
5. check end traveling gears condition and do the greasing. It is ok.

HT.
1. check rope drum, hook, rope condition. greasing of rope. It is ok. Greasing is done.
2. check all fasteners and mounting bolts. It is ok.
3. check frame welding conditions. It is ok.
4. gearbox oil level is ok.		OtherTAPPING SEC. CRANE NO. 3
1502823 Sep 2020Scheduled Maintenance3RD FLOOR CARBON PASTE LIFTING CRANE

LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing. Greasing is done.
2. check the gearbox oil level, leakage, and fill if required. It is OK.we fill grease due to leakage.
3. check all fasteners and mounting bolts.it is ok.
4. check frame welding conditions.it is ok.
5. check end traveling gears condition and do the greasing. It is ok.greasing is done.
6.
CT.
It is ok. Gear bearing is ok.


HT.
It's is ok. Pulley's condition is ok.no greasing because of grease is already there.		OtherCARBON PASTE LIFTING CRANE
1502923 Sep 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 2

LT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

CT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

HT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly. 		OtherTAPPING SEC. CRANE NO. 2
1503023 Sep 2020Scheduled MaintenanceTAPPING SECTION E.O.T. CRANE 3

LT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

CT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.

HT.
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform. checked. it is ok.
2. check panel board, clean, & tight all loose parts. clean and tight loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.it is ok. working properly.		OtherTAPPING SEC. CRANE NO. 3