| 14401 | 02 Dec 2020 | Breakdown Maintenance | It's motor is burn. We removing pump no. 3 and give it for rewinding. | Other | POLLUTION 1 | |
| 14402 | 02 Dec 2020 | Scheduled Maintenance | We add one small cyclone seprator with pump no. 4. We giving 4 inch pipe connection from pump and fit one 8 inch 90 degree bend on it. Down side we make one 45 degree bend of pipe 2 inch. We fit one butterfly control valve in 4inch pipe line. | Other | POLLUTION 1 | |
| 14403 | 02 Dec 2020 | Scheduled Maintenance | We give connection from pump no. 1 one 6 inch pipe with big bend 90 degree to pollution pit. And weld one 12 inch pipe with 8 and 6 inch pipe at discharge side. | Other | POLLUTION 1 | |
| 14404 | 02 Dec 2020 | Scheduled Maintenance | Pump not supply water so we tight gland rope. Now it's ok. | Other | GRANULATION TANK (FURNACE 1) | |
| 14405 | 01 Dec 2020 | Other | For mansa one 1000 mm width conveyor fabrication work is in progress.
its fabrication work is complete. | Other | BLUE OCEAN | |
| 14406 | 01 Dec 2020 | Scheduled Maintenance | WATER CIRCULATION PUMP 1,2,3,
FURNACE 1
GRANULATION PUMP 1,2
SUBMERSIBLE PUMP 1,2,
POLLUTION WATER PUMP NO 1
FURNACE 2
GRANULATION PUMP 1,2,
POLLUTION WATER PUMP NO 1,
OFFICE SUBMERSIBLE PUMP 1,
WASHING PLANT SUBMERSIBLE PUMP 1
1. check the pump condition and check discharge.
2. check coupling condition, alignment, and do greasing.
3. check pipelines and valve's condition.
4. check cooling towers nozzles condition.some NOZZLE ARE damaged. We change it. Now it's ok.
| Other | PUMP | |
| 14407 | 01 Dec 2020 | Scheduled Maintenance | F1- GRANULATION MOTOR 1,2 WATER CIRCULATION PUMP MOTOR 1,2,3, SUBMERSIBLE PUMP MOTOR 1,2, POLLUTION WATER PUMP MOTOR
NO 1
F2- GRANULATION MOTOR 1,2, POLLUTION WATER PUMP MOTOR NO 1, OFFICE SUBMERSIBLE PUMP MOTOR 1,
WASHING PLANT SUBMERSIBLE PUMP MOTOR1
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.
2. check panel board, clean, & tight all loose parts.
3. all parts clean by hand blower.
4. water circulation pump motor greasing.
| Other | PUMP | |
| 14408 | 30 Nov 2020 | Scheduled Maintenance | ALL CONVEYORS
BC 1, BC 2, BC 3, BC 4, BC 5, BC 6, BC 7
1. check motor condition ( amp, volt, and connectivity) if the noise coming than inform.
2. check panel board, clean, & tight all loose parts.
3. all parts clean by hand blower.
4. check limit switches and its condition. ensure that all limit switches and wires working properly.
| Other | RMHS CONVEYOR | |
| 14409 | 30 Nov 2020 | Scheduled Maintenance | ALL VIBRATORS
check Vibro feeders coil connection, its condition and ensure its working properly with adjusting its vibrations. | Other | RMHS VIBRO FEEDER | |
| 14410 | 30 Nov 2020 | Scheduled Maintenance | ALL CONVEYORS
BC 1, BC 2, BC 3, BC 4, BC 5, BC 6, BC 7
1. greasing of bearings.
Grease is already there. Tomorrow we will greasing again.
2. lubrication of rollers and check conditions.
3. check belt status ( if damaged than inform and change) and also check tightness, speed.
BC 2 BELT CHANGED.
4. gearbox oil level check and if not then fill as per requirement.
5. check coupling and key ( if damaged than inform and change) and do the greasing.
6. check the drum condition.
7. check mounting frame welding condition.
8. check rollers condition and if not good then change.
SOME ROLLERS AND ALL RETURN ROLLERS CHANGE FOR BC2 | Other | RMHS CONVEYOR | |
 white.png){kind=small}