| 13561 | 12 Mar 2021 | Breakdown Shutdown | Electrode 3 sparking. We putting clay with paste to electrode 1 and 3 side. | Furnace I | ELECTRODE 3 | |
| 13562 | 12 Mar 2021 | Breakdown Shutdown | Electrode 3 sparking. We tighting bolts. Now it's ok. It's clamp c6 has water leakage. We putting pulp. | Furnace I | ELECTRODE 3 | |
| 13563 | 12 Mar 2021 | Breakdown Shutdown | Electrode 3 sparking we fighting bolts. It's c6 clamp also leakage. We putting pulp. | Furnace I | ELECTRODE 3 | |
| 13564 | 12 Mar 2021 | Breakdown Shutdown | It's clamp no. C3 bolts coming out. We switch off furnace and fitting new bolt. Now it's ok. | Furnace I | ELECTRODE 3 | |
| 13565 | 12 Mar 2021 | Breakdown Maintenance | Crane not working. When we check found that it's motor flange to body allen key bolts are damaged. We open motor and bring it to workshop. After that we found that it's inside bearing 6208 is damaged. We replace bearing with allen key bolts and fitting it. Now it's ok. | Other | TAPPING SEC. CRANE NO. 1 | |
| 13566 | 11 Mar 2021 | Scheduled Maintenance |
Breakdown due to break liner. Finish.
CHIPPING YARD E.O.T. CRANE 1
LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing.
2. check the gearbox oil level, leakage, and fill if required.
3. check all fasteners and mounting bolts.
4. check frame welding conditions.
5. check end traveling gears condition and do the greasing.
CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing.
2. check the gearbox oil level, leakage, and fill if required.
3. check all fasteners and mounting bolts.
4. check frame welding conditions.
5. check end traveling gears condition and do the greasing.
HT.
1. check rope drum, hook, rope condition. greasing of rope.
2. check the thruster drum condition and its brake tightness.
3. check all fasteners and mounting bolts.
4. check frame welding conditions.
| Other | CHIPPING YARD CRANE NO. 1 | |
| 13567 | 11 Mar 2021 | Scheduled Maintenance | CHIPPING YARD E.O.T. CRANE 2
LT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing.
2. check the gearbox oil level, leakage, and fill if required.
3. check all fasteners and mounting bolts.
4. check frame welding conditions.
5. check end traveling gears condition and do the greasing.
CT.
1. check coupling, shaft, and pedestal bearing condition and do the greasing.
2. check the gearbox oil level, leakage, and fill if required.
3. check all fasteners and mounting bolts.
4. check frame welding conditions.
5. check end traveling gears condition and do the greasing.
HT.
1. check rope drum, hook, rope condition. greasing of rope.
2. check the thruster drum condition and its brake tightness.
3. check all fasteners and mounting bolts.
4. check frame welding conditions.
| Other | CHIPPING YARD CRANE NO. 2 | |
| 13568 | 11 Mar 2021 | Scheduled Maintenance | TELPHER FOR F1
1. checking the bearing, rollers condition, and do lubrication.
2. checking frames welding condition.
3. checking cotter pin and its failure condition.
| Other | TELPHER (FURNACE 1) | |
| 13569 | 11 Mar 2021 | Scheduled Maintenance | TELPHER FOR F2
1. checking the bearing, rollers condition and do lubrication.
2. checking frames welding condition.
3. checking cotter pin and its failure condition.
| Other | TELPHER ( FURNACE 2) | |
| 13570 | 11 Mar 2021 | Scheduled Maintenance | POLLUTION ID FANS (Furnace 1)
1. open cover and clean dust.
2. check the balancing of impeller and vibration isolation.
3. check v belts condition and inform if its on critical stage.
4. check foundation bolts and nuts of Plummer blocks.
5. greasing the Plummer blocks.
6. check the duct condition and remove dust from the duct.
7. check stack condition and check its temperature.
| Other | POLLUTION 1 | |
 white.png){kind=small}